Pressure Sensor Switch

$101.31 + $6.99 Shipping — per order
List Price $129.41 | Save 22%
Part Number PD00003222
Manufacturer Part W10415587
Manufactured By Whirlpool OEM
In Stock
This item is in stock and ships today.
VIEW CART

We have FAST flat rate shipping

Standard (2-7 business days) - $6.99 per order

Need it faster?

Part Description

Front Load Washer Water Level Senor Pressure Switch.  This is a new GENUINE Whirlpool replacement part.

This part is used on some Whirlpool Duet, Maytag Epic, and Kenmore Elite HE steam washing machines.

Compatible Brands

  • Kenmore
  • Maytag
  • Whirlpool

View Model Cross Reference Table

This Part PD00003222 (Mfg #W10415587) replaces these parts:

  • W10156252

Our Competitor’s Part Numbers for this part

  • 1938628
  • AP5264563
  • PS3497663
  • EAP3497663

Repair Stories

Sort By Helpfulness Highest | Lowest
+1
Helpful? Yes | No
Part
  • Pressure Sensor Switch
Product Rating
Customer
Jessie from MT
Problem

Receiving F02 code and SUDS code

Tools

Nut driver and flat head screwdriver or needle nose pliers

Repair & Advice

Was receiving F02 and SUDS error code. The pump had not pumped the water out in a predetermined amount of time (even though it had). The SUDS error would immediately come on even without soap. Figured it must be the sensor giving bad information to the control panel. Changed the pressure switch and that fixed the problem. Has been running over a month with no problems. First, you may want to clean the pump filter out first. The pump filter is accessed by removing the 3 screws on the front lower panel of the washer. You will see a plastic handle front and center when you remove the panel. Twist the handle and pull to remove. Have plenty of towels or wet/dry vac ready as some water will flow out. Remove debris for filter. Replace panel and run washer cycle again to see if problem is resolved. Also check drain hose to make sure it isn't stopped up. If not, it may be the pump or pressure switch. My pump was removing the water in a reasonable amount of time so i figured it was the water level pressure switch. To replace the switch remove the 3 nuts at the top and back of the washer. The top should slide right out by pulling it towards the back of the the washer. the pressure switch is at the top back right corner of the washer, close to where the drain hose comes through the back of the washer. Use the flat head screwdriver or needle nose pliers to push in the plastic tab so as to disengage the plastic catch. Replace with new part. Replace panel cover.

0
Helpful? Yes | No
Part
  • Pressure Sensor Switch
Product Rating
Customer
stephen from FL
Problem

Pressure sensor not working

Tools

Screw driver

Repair & Advice

Tale off lid, sensor in back right, swap them out

Model Cross Reference

This part PD00003222 (Mfg #W10415587) works with all models listed.
Manufacturer Appliance Model Description
Maytag MHWE500VW11 5000 Series Steam Washer
Whirlpool WFW9500TW00 Duet Steam Washer
Whirlpool WFW9500TW01 Duet Steam Washer
Whirlpool WFW9600TA00 Duet Steam Washer
Whirlpool WFW9600TA01 Duet Steam Washer
Whirlpool WFW9600TB00 Duet Steam Washer
Whirlpool WFW9600TC00 Duet Steam Washer
Whirlpool WFW9600TU00 Duet Steam Washer
Whirlpool WFW9600TW00 Duet Steam Washer
Whirlpool WFW9600TW01 Duet Steam Washer
Whirlpool WFW9600TZ00 Duet Steam Washer
Whirlpool WFW9700VA00 Duet Steam Washer
Whirlpool WFW9700VW00 Duet Steam Washer