Shipping Options

View more details in our Shipping Policy

All shipping rate advertisements assume delivery to continental US address, and that the part is in stock and is not oversized.

Shipping rates are per order, not per part!

Standard – $10.99
Estimated arrival
Thursday Mar 21–26
Quicker – $24.99
Estimated arrival
Thursday Mar 21
Quickest – $33.99
Estimated arrival
Wednesday Mar 20

Monthly Archives: October 2011

How To Remove & Install Drain Pump W10536347

Removing drain pump part number W10536347 is a simple task.  When this pump fails, the washer will display “LD” on the display which means “Long Drain”.  This pump can be found on Whirlpool Cabrio, Maytag Bravos, and Kenmore Oasis model washing machines.  The pump can fail if something gets stuck in the pump (coin, clothing item, ect), and sometimes you can get lucky and just remove the object that was stuck in the pump.  Other times the pump can break, so make sure so inspect the pump before putting it back in the washer.

How to the remove the drain pump:

  1. Unplug the washer
  2. Next, you will need to remove any water still in the washer (use a wetvac, bucket, towels, ect to do this)
  3. Turn off the water supply going to the washer & disconnect the hot & cold fill hoses to the washer
  4. Remove the drain hose from the wall or drain tub
  5. Tape the lid shut (so the lid doesn’t pop open)
  6. Carefully lay the washer down on its front side (place some towels or rugs on the floor to protect the washer).
  7. Note:  On the bottom side of the washer, the drain pump is the larger of the two pumps (the recirculation pump is the smaller one).
  8. Remove the drain hose (discharge hose) from the pump.  Loose then clamp and pull off the hose.  Note there is a notch in the hose to line up when you put the hose back on.
  9. Remove the inlet hose to the pump.  Loosen the clamp and remove the hose from the pump.
  10. Open the end cover on the pump and remove the wire connector.
  11. Remove the three 5/16″ screws securing the pump.
  12. The pump should now be free.  Check to see if anything is caught in the impeller.  If you notice any damage, or the pump still does not work then you will need to replace the drain pump assembly.
  13. Re-install in the reverse order.  NOTE:  The new pump includes a shield cover that goes between the pump and tub of the washer to protect the pump from any moisture falling onto it.

If you have any questions please post them in the comments section below.

If you need to purchase a new drain pump for your washer, visit our store by clicking the link below:

Drain Pump and Motor – W10536347

How To Install & Remove W10189966 Control Board

Removing and installing the W10189966 motor/machine control board in your washer is an easy task.  This control board is used on some Whirlpool Cabrio, Kenmore Oasis, and Maytag Bravos model washers.  When this control board fails, they will commonly come up with an F1 error code repeatedly that won’t go away.

  • First unplug the washer
  • Next, remove the three hex screws from the rear of the top console.
  • Then Lift the console off the cabinet and disconnect the cable going to the user interface board.  This will give you access to the motor/machine control board.
  • Disconnect the nine wire connectors going to the control board and the pressure switch hose (also called a pressure transducer tube).
  • Remove the mounting screw and lift the front of the control, slide it out from under the clips at the back, and remove it.
  • Re-install the new control board in the reverse order.

If you have any questions, please post them in the comments section below.

Visit our store if you need to purchase a new control board for your washing machine by clicking the link below:

Machine/Motor Control – W10189966

Parts Dr

Our customers matter a lot to us! So we provide YOU with as much information on repairing your appliance as possible. And its all FREE!

Categories

Locate Model Number

Choose your appliance type